Full metadata record
| DC pole | Hodnota | Jazyk |
|---|---|---|
| dc.contributor.author | Polák, Roman | |
| dc.contributor.author | Zahálka, Martin | |
| dc.date.accessioned | 2019-03-04T11:50:33Z | - |
| dc.date.available | 2019-03-04T11:50:33Z | - |
| dc.date.issued | 2018 | |
| dc.identifier.citation | POLÁK, R., ZAHÁLKA, M. Influence of gate position during the injection moulding process. In: Annals of DAAAM and Proceedings of the International DAAAM Symposium. Vídeň, Rakousko: DAAAM International Vienna, 2018. s. 659-664. ISBN 978-3-902734-20-4 , ISSN 1726-9679. | en |
| dc.identifier.isbn | 978-3-902734-20-4 | |
| dc.identifier.issn | 1726-9679 | |
| dc.identifier.uri | 2-s2.0-85060102790 | |
| dc.identifier.uri | http://hdl.handle.net/11025/31136 | |
| dc.format | 6 s. | cs |
| dc.format.mimetype | application/pdf | |
| dc.language.iso | en | en |
| dc.publisher | DAAAM International Vienna | en |
| dc.relation.ispartofseries | Annals of DAAAM and Proceedings of the International DAAAM Symposium | en |
| dc.rights | Plný text je přístupný v rámci univerzity přihlášeným uživatelům. | cs |
| dc.rights | © DAAAM International Vienna | en |
| dc.title | Influence of gate position during the injection moulding process | en |
| dc.type | konferenční příspěvek | cs |
| dc.type | conferenceObject | en |
| dc.rights.access | restrictedAccess | en |
| dc.type.version | publishedVersion | en |
| dc.description.abstract-translated | This article deals with the influence of the gate position on the final properties of a plastic product after the injection moulding process. Parameters such as temperature, fibre orientation and filling velocity are evaluated. The importance of the internal fibre orientation on the mechanical properties is also described. Advanced virtual mould-flow analysis is used for this research. A simple brick from Polybutylene Terephthalate (PBT) with 30% of short glass fibres is chosen as the reference part. A virtual model of PBT is described in depth in this article. An injection process with the same initial parameters was used for three different locations of the pin gate. This type of gate is considered because it is one of the most frequently used in the plastics industry. Different kinds of gates and their influence on filling are also briefly described. This paper shows the importance of the gate location and it also helps to understand the flow of short fibre reinforced thermoplastics inside the mould cavity. The article presents an in-depth and complex view of the issue of mould filling. | en |
| dc.subject.translated | injection moulding | en |
| dc.subject.translated | gate | en |
| dc.subject.translated | filling | en |
| dc.subject.translated | fibre orientation | en |
| dc.identifier.doi | 10.2507/29th.daaam.proceedings.095 | |
| dc.type.status | Peer-reviewed | en |
| dc.identifier.obd | 43924171 | |
| dc.project.ID | LO1502/RoRTI - Rozvoj Regionálního technologického institutu | cs |
| Vyskytuje se v kolekcích: | Konferenční příspěvky / Conference papers (KKS) OBD | |
Soubory připojené k záznamu:
| Soubor | Velikost | Formát | |
|---|---|---|---|
| INFLUENCE OF GATE POSITION DURING THE INJECTION MOULDING PROCESS.pdf | 1,05 MB | Adobe PDF | Zobrazit/otevřít Vyžádat kopii |
Použijte tento identifikátor k citaci nebo jako odkaz na tento záznam:
http://hdl.handle.net/11025/31136Všechny záznamy v DSpace jsou chráněny autorskými právy, všechna práva vyhrazena.